Girls Knit Tunic Tutorial
- +/- 1 yard of fabric (Depends on what size you are making and the length you want. I used a bit less than 3/4 yard for a 5/6 tunic length top and could have made a knee length dress with 1 yard.)
- 1/2 elastic for the waistline
- Ball point needle (plus optional Stretch Twin Needle)
- ruler/measuring tape/scissors/fabric marker plus other basic sewing supplies
- loose fitting t-shirt to trace, like a regular fruit of the loom or hanes t-shirt
- large paper to trace the pattern on (wrapping paper, art paper or freezer paper all work well)
- iron and spray starch (if needed)
Products used and recommended for this project: (My favorite fabric shop for knits: Funkalicious Fabrics and Girl Charlee.)
- My Sewing Machine: SINGER 9960 Quantum Stylist
- My Serger: Brother 1034D 3 or 4 Thread Serger or you can just use Pinking Shears
- Rotary Cutter
- I love my large ruler and large cutting mat, but you may prefer to start of with a smaller Cutting set
- Dritz Dual Purpose Marking Pen and Fray Check
- Ball Point needles
- Singer walking foot or universal walking foot
- Blind hem foot.
- Wonder clips (I didn’t use these in the post, but they are just awesome!
All seam allowances are 1/2 inch unless otherwise stated.
Step one: Create your pattern and cutting the fabric pieces.
With the measuring tape, measure from the shoulder to the desired length of the top. Add 1.5 inches to this measurement.
Fold your t-shirt in half, back facing out, smoothing out as many wrinkles as possible. Follow the directions below to create your pattern: (I left the image large, so you can right click and open in a new window to see it better.)
After tracing the basic pattern, widen the neck line just a bit to create more of a “boat-neck”.
Lower the front neckline by about 7/8 of an inch at the lowest point. Draw the front neckline right onto the same pattern piece.
Cut out your pattern. Fold your fabric so the stretchy-ness runs side to side (selvage to selvage) and line up the folded edge of your fabric with the fold-edge of your pattern and cut out the back piece.
Refold your fabric and cut out the front piece. Don’t forget to use the pattern mark for the front neckline. To make things easier, I use my tracing wheel and tracing paper on the front neckline mark.
Step 2: Assembling the shirt.
Fold the back neckline edge over 1/2 inch toward the wrong side and pin in place. If your fabric is giving you difficulties, try pressing the edge and using spray starch.
Using a stretch twin needle or a narrow zig zag stitch set at a medium length, sew the hem in place. Be sure to remove the pins before you get to them. Running over a pin will stretch out the fabric. Repeat this for the front piece.
Right sides together line up the shoulder edges and necklines, pin in place. Use a serger or a straight stitch, on your machine and sew the shoulder seams using a 1/2 inch seam allowance. (Don’t forget to lengthen the stitch width and to loosen the needle tension a tiny bit, and do a few practice runs on some of your scraps!)
For the sleeve hem, you can choose to leave this edge raw. If you do, you may want to trim the 1/2 inch seam allowance from the sleeve edge.
To hem the sleeve, fold the arm hems over 1/2 inch and sew this hem line with a twin needle or zig zag stitch. Be sure to remove the pins before you get to them. Running over a pin will stretch out the fabric.
Next, line up the sides of the shirt, right sides together and sew with your serger or a straight stitch on your sewing machine.
Step 3: Adding the casing, belt or shirring the waistline.
I originally wanted a belt for this tunic top, but after making a practice top, I decided a belt would not be practical for school. It was really cute though, and if you would like to add a belt, I will include the directions at the bottom of the tutorial. (The top is not as cute in this solid fabric, but I loved the belt:)
After deciding against the belt, I planned on shirring the waistline. I love to shirr with elastic thread, it is a very easy option. My machine was acting up and I couldn’t get the shirring to work. (I did take my machine in for a tune-up and the repair man said the bobbin needed a tension adjustment.) If you want to shirr your waistline, follow the placement guide below and I have some great shirring instructions on this post.
The best way to decide where to put the waist band is to just have your model try it on and mark the spot with a fabric marker. If your model is not available here is what I suggest:
2/3t:: 1.5 inches down from sleeve edge
4/5: 2 inches down
6/7/8: 2.5 inches down
Decide where you want the waist line to be and mark the spot on both sides. Use a ruler and fabric marker and connect the marks on both sides of the tunic top. (Working on a striped fabric made it really easy to line up my casing.)
Cut a strip of your knit fabric 1 1/8 inch by the width of your shirt (all the way around) plus 1 1/2 inch. You can also use bias tape, but do not use regular cotton fabric unless it is cut on the bias.
Line the top of the fabric strip up with your waistline mark and pin in place.
Sew the strip into place using a straight stitch about 1/8 inch from the edges. When you get to the end, you should have a tiny bit of fabric strip left. Trim it off or just keep sewing and overlap the edges. (If you look closely below, you can see where I over lapped the fabric.) Be sure to leave about a 1 inch opening to thread the elastic through.
Measure around your model’s waist and subtract 1 inch. Cut a piece of 1/2 inch elastic to this measurement. Using a safety pin, thread the elastic through the casing. Once you are satisfied with the fit, sew the elastic together using a very tight zig zag stitch. Trim the elastic edges and close up the casing.
Step 4: Hemming the bottom.
You can choose to leave the bottom hem raw or hem it with a twin needle or zig zag stitch. Fold your hem up 1/2 inch. (or more if you left it long like I did.) Sew right along the edge and carefully trim away any excess fabric.
That’s it, You’re done! (So cute, she wore the top to school on Friday and told me that a few girls told her they liked her top!)
*To add a belt, you can use an embroidery needle and thread and create a little belt loop in the side seam at your waistline marking. For the belt width and length, I suggest a 4 1/2 inch by about 60 inch piece of fabric. Fold the fabric in half, right sides together, long ways, and sew all the way around, leaving a 2 inch opening in the middle. Turn the belt right side out through the opening and close the opening either by hand or with your machine.
I hope this tutorial inspires you to make a top or just try practicing on knits. If you do make a top, please come back and share the link in the comments or if you don’t have a blog Facebook Page or tag me on Instagram.