A couple of weeks ago, I teased you about the Bubble Fountain my hubby had made for me last summer. I’ve finally taken a few moments to write up the instructions on how to make a Bubble Fountain in a Pot, so you can make one too!
We have a local water garden shop that is the most amazing place to go and browse. They have 5 acres of the most beautiful ponds and streams and fountains on display. It is so pretty, they’ve even opened up their their location as a venue for parties and weddings.
I’d been wanting to add a small water feature to my side garden, where all the birds hang out (check out this recent shot of the birds.) The first place I thought to go was our local
Water Garden shop. (The Hill Country Water Gardens- seriously, if you are in the Texas Hill Country and are in the market for a fancy pond or water garden, you should really visit this place. The inspiration alone is crazy-good!)
As beautiful as this place is, their services and products aren’t cheap and are out of the price range of someone on a super tight budget. After a significant amount of browsing, I just couldn’t find exactly what I wanted. Plus, not a not a single bubble pot that I liked was less than $150 – and that was just for the pot!
After consulting with the hubby, we decided to hit our local big box hardware store and see if we could find what we needed to make our own bubble fountain.
I am so glad we did, we spent more than 3/4 less than what we would have spent had we not made our own fountain. (If I had used a pot I already had, it would have been just the cost of the pump, tubing and gravel.)
It wasn’t easy putting instructions together since I didn’t get step by step photos of the project as it was happening, but the process is really simple. I’m certain you can get the idea of what to do from the diagram below.
Supplies Needed: (you should be able to find all these items at your local big box hardware store or on Amazon)
- Submersible pump
- clear vinyl tubing (whatever size goes with your pump)
- 1 small and one large waterproof pot w/ no drainage holes. (Plastic or the fake stone-looking pots)
- something for the small pot to sit on (upside down pot, brick or a cinder block)
- drill and bit
- Several medium sized rocks
- bag of pea gravel or small decorative river rock
- clear waterproof silicone caulk/sealant
- electrical supplies needed to splice the electrical cord
Step 1: Cutting and splicing the electrical cord: ***This step is only necessary if you don’t want your cord to be seen. If your fountain is in a corner or up against the a wall, you might be able to just drape the electric cord over the edge and hide it. If this is the case skip to step 2.***
Drill a small hole near the bottom of the large pot. The diameter of the hole should be just big enough for the pump power cord. Cut the pump power cord in half – somewhere in the middle.
Thread the pump cord through the hole you drilled and splice the cord back together. (I found these two helpful tutorials on splicing an electrical cord and making it semi-water resistant. Hubby said he took this extra step of making the splice semi-water resistant since we buried the cord under the mulch. He also said he also used some sort of wire netting around the outside of his splice to make it more secure before the silicone and tape.)
Step 2: Assembling the potsStack the brick or upside down pot at the bottom of the larger pot. Add a couple of larger rocks around the bottom of the pot and find a secure spot for the pump to rest.
Add a few large rocks to hold the tubing in place. (This may take two people) Make sure the end of the tube will sit right below the water line. (Keep it long, so you can trim it later.)Seal the drilled holes with the silicone caulk. Follow the package instructions on how long to wait before adding water. (I think we waited 24 to 48 hours.)Once the silicone is dry, add water to test the silicone seals and add more silicone if you have any leaks. (Ours has been going strong for a year.)
Step 3: Making it pretty:
Add more of the bigger rocks as needed.
Add pea gravel/small decorative rocks to the pots as needed, just to a couple of inches below the rim. This will also help keep the tube in place.
You can also add the pea gravel/small river rock to the larger pot, but do not cover the pump. You can almost see how we used a larger rock to keep the space around the pump clear in this picture:
Now, if after reading all that, it just sounds too hard- Amazon has some nice ready to go ones for a few more $$.
Fill with water and turn on the pump. Trim the tube a tiny bit at a time to get the proper bubbling- be careful not to trim too much, because you have siliconed the tube in at the bottom.Enjoy your Bubble Fountain!
Looking for more budget friendly DIY outdoor projects? Be sure to check these out:
Feedly, Bloglovin', your favorite feed reader, or by signing up via email. Just click on one of the icons below: