christmas | Christmas Sewing | home sewing tutorials | quilts | Sewing | Uncategorized

Quilted Tablet PC Cover

Today, I am sharing how i made this quilted cover for my tablet!

A new tablet has been on my wish list for a while and I finally bought one with my Christmas money!  I also grabbed a silicone skin cover (hot pink of course), Tablet Stand and screen protector.  The only thing I still needed was a protective case for when I wasn’t using it or when traveling.

I looked around on Amazon, but I wasn’t finding anything I liked online. (Gotta get my money’s worth out of the Amazon Prime membership I just paid for.)  After contemplating what I wanted, I decided to just make my own padded Tablet Cover.

tablet PC Cover tutorial

It was really very easy.

Disclosure: This post may contain affiliate links.

To make a quilted tablet cover, you need:

-2 Fabric pieces, one for the outside and one for the inside.  (For my outside fabric I pieced together  fabric scraps.)
-Quilt Batting (You could also use fleece or felt)
-Elastic cording
-Button
-Thread
-Cutting mat and ruler with bias markings (you can manage without bias marking, but it sure makes it easier)
-water soluble marker
-scissors
-fray check

First, you need to determine the width to cut your fabric.  

Here is how to get measurements for your device:

  • width of the device + the depth of the device + 2.5 inches

For me those numbers were 10.25 + .5 + 2.5.  I wanted a little extra wiggle room since I have a silicone skin on mine, so I added an additional .5 inch.

I could give you a long mathematical computation for the length of fabric needed, but it will be a lot easier if you just cut the fabric to 3.5 times the length of your device.  Then just play with how big you want your pocket and how much you want the flap to fold over.  Once you have the pocket and flap size to your liking, add one inch for seam allowances and trim off any extra fabric.  

I didn’t take a picture of this process, but here is a close up of how mine looks in the pocket and with the flap folded over:

 

The total fabric dimensions I used for a Galaxy Tablet was 13 3/4 wide by 22 7/8 long.  (My silicone skin adds a tiny bit to the measurement all the way around and I based my measurements with the skin on.)  If you have an Ipad you could adapt the fabric measurement by taking off 1 1/2 inches from the width.  

 

Next, cut your second fabric piece to the same dimensions as the first piece.  Cut the batting to the same width and 1/2 inch shorter on the length. (This helps when we finish the open end.)

Lay your fabrics together in this order:

  • Top fabric right side up, 
  • bottom fabric right side down
  • then the batting (fleece or felt)

Next, sew the 3 edges together, using a 1/2 inch seam allowance, leaving the top open as shown:

Clip the bottom corners and trim away extra fabric from the sides.

Then flip the cover right side out, so the batting is on the inside, sandwiched between the top and bottom layer.  Use a pencil or point turner to help get a crisp corner.

Iron the seam edges flat.

Remember how you cut the batting 1/2 inch shorter and left the short edge open?  Fold the fabric edges in 1/2 inch all the way around the opening and press the edges as evenly as possible.  Pin in place.

Cut your elastic cord to about 7 inches. Find the center of the pocket flap and mark it.  Fold the cord in half and tuck in about an inch between the folded edges at your center marking.  Pin securely.

Sew the edge closed 1/4 inch from the edge.

When you get to where the cord is tucked in, backstitch over the cord 2 times, so it is extra secure.

Next, we will mark the quilting lines with our disappearing ink marker.  Line your fabric up on the cutting mat, then line up your ruler using the 45 degree bias markings.

With your marker, draw lines 2 inches apart all the way across the fabric.

Then flip your fabric around and draw more lines going the other direction.  You will end up with a criss-cross pattern like this:

Sew all the way across, edge to edge, along each line you drew.  Pull all your treads to the back/inside piece, tie securely and trim.  Use fray check on the knots to ensure they are extra secure.

Next, lay out your fabric flat.  Use your judgment on how much room you want in your pocket and how much overlap you want with the flap.  Mark the edge of the pocket and pin in place.

Start sewing from the top of the flap to the bottom edge of the pocket, about 3/8 inch from the edge.  Repeat on the other side.

You’re almost done, the only thing left is to sew on the button.  Just close the flap and use the cord loop as a guide for button placement.

 how to sew a cover for an ipad or kindle fire

 

Tada! You’re Done!  

Now sit back and admire your new handmade Quilted Tablet Cover!  If you are inspired to create something based on this tutorial, I would love to see it!  

 

 

 

Don't miss any more posts!

Follow along on:

FeedlyBloglovin', your favorite feed reader, or signing up via email and have new posts delivered to your email box each week!